Fall Restraint Systems Must Meet Which of the Following Criteria

Unlike the personal fall-arrest system which is designed to stop a fall a personal fall-restraint system prevents a worker from reaching an unprotected edge and thus prevents a fall from occurring. Shock-absorbing Lanyard PASS FAIL.

Fall Arrest Systems And Training Fall Protection Blog

Fall restraint systems must meet which of the following criteria.

. The thimble must be firmly seated in the eye of the splice and splice should have no loose or cut strands. All of the above. Must be visually inspected by the trained user prior to using.

When utilized a restraint system shall meet the following criteria. Anchorage strength of a minimum of 3000 lbs C. However at a minimum fall restraint systems should have the capacity to withstand at least 3000 pounds of force or twice the maximum expected force that is needed to restrain the worker from exposure to.

OSHA has no specific standards for fall restraint systems. Anchorage strength of a minimum of 3000 lbs. A A dielectric test of 8197 volts AC.

Guardrail systems need to meet the following criteria. Fall restraint systems must meet which of the following criteria. I The walkways must be at least 12 inches wide.

3 major components of a personal fall arrest system. 2 The employee cannot free-fall more than 6 feet or contact any lower level. The attachment point to the body belt or full body harness can be at the back front or side D.

1 The maximum arresting force on an employee must be limited to 1800 pounds. Physically prevent the user from reaching an unprotected edge andor fall from or through the structure. B Personal fall restraint systems must conform to the criteria in WAC 296-880-40025.

Which of the following can be used to prevent complacency from happening to use or to those around you. 4 Lanyards and vertical lifelines must have a minimum breaking strength of 5000 pounds 222 kN. B Be rigged such that an employee cannot fall more than 6 feet.

Prevent the user from reaching areas where free fall could occur B. Keeper locks must prevent the keeper from opening when the keeper closes. Which of the following is an across-the-board corrective action that might be implemented as part of an incident investigation.

The system consists of an anchorage connectors and a body harness or a body belt. Personal fall arrest system connectors must be compatiable and capable of supporting. 2 For nonassemblydisassembly work on cranesderricks except tower cranes the employer must provide and ensure the use of fall protection equipment for employees six feet or more above a.

Designed by qualified person for fall protection D. Fall restraint systems must be anchored to any part of the equipment that is capable of withstanding twice the maximum load that an employee may impose on it during reasonably anticipated conditions of use. Linemans body belt and pole strap systems must meet the following tests.

Ii Guardrails railings and other permanent fall protection attachments along walkways are. 19261423 h Tower cranes. If the personal fall arrest system meets the criteria and protocols in appendix D of this subpart.

6 A properly designed Personal Fall Arrest System must choose three a Limit maximum arresting force on employee to 1800 pounds when using a body harness. The focus of this article is the plan for fall arrest systems. Anchor and the anchorage connector full body harness and _____ B.

All the above correct answer. Designed installed and used under the supervision of qualified person as part of a complete personal fall protection system that maintains a safety factor of at least two. We suggest that as a minimum fall restraint systems have the capacity to withstand at least three thousand 3000 pounds of force or twice the maximum expected force that is needed to restrain the person from exposure to the fall hazard.

3 The employee must be brought to a complete stop and the deceleration distance of travel must not exceed 35 feet. Fall restraint systems must meet which of the following criteria A. B Prohibited on booms supported by pendant ropes or bars if the guardrailsrailings.

This includes the edge of excavations greater than six feet in depth. Guardrails are needed at the edge of work areas 6 feet or more in height to protect employees from falling. Travel restraint lines must be capable of sustaining a tensile load of at least 5000 pounds 222 kN.

C Positioning device systems must conform to the criteria in WAC 296-880-40030. Fall restraint systems must meet which of. When personal fall arrest systems are employed they must meet the following criteria.

Personal Fall Arrest Systems must meet the following four criteria. A travel restraint tether line defined in 1910140 b means a rope or wire rope used to transfer forces from a body support to an anchorage or anchorage connector in a travel restraint system. The edges of the thimble must be free of sharp edges distortion or cracks.

If the personal fall arrest system meets the criteria and protocols contained in Appendix C to subpart M and if the system is being used by an employee having a combined person and tool weight of less than 310 pounds 140 kg the system will be considered to be in compliance with the provisions of paragraph d16 of this section. Travel restraint system means a combination of an anchorage. 2 Connectors must have a corrosion-resistant finish and all surfaces and edges must be smooth to prevent damage to interfacing parts of the system.

Prevent the user from reaching areas where free fall could occur B. All of the above. Anchorages except window cleaner belt anchors must be capable of supporting at least.

1910140 c 14 Travel restraint lines must be capable of sustaining a. Force to firmly close the keeper. 3 When vertical lifelines are used each employee must be attached to a separate lifeline.

Toprail is 42 inches - 3 inches above the walkingworking level.

What Qualifies As A Safety Anchorage Point For A Personal Fall Arrest System